The CompuDry® Command Center constantly monitors conditions such as grain moisture, grain temperature, and plenum temperature, while also controlling all components of the system. Designed with the operator in mind, it is easy to use with fingertip control of your entire drying process.

With the addition of a Turbo-Booster to the Blue Flame™ Dryer, you can increase drying capacity in any counter-flow performance system.

This control box is used to keep the grain level between two limit switches in a grain drying bin. The grain is supplied from a wet holding tank. The control will turn on a horizontal feed auger and an inclined fill auger when the drying bin requires grain.

The Rotation Detector will monitor any rotating shaft or pulley and will activate a relay if the rotation speed is outside the pre-programmed limits. It is normally installed and wired to start monitoring when a motor is started.

With the addition of a Turbo-Booster to the Blue Flame™ Dryer, you can increase drying capacity in any counter-flow performance system.

This timer kit controls all Continuous Flow and Auxiliary Augers connected to the CompuDry® Command Center. When the Low Grain Shut-Off shuts down the system, the augers set to automatic will run for the time delay set by this timer.

Used to measure back pressure in the plenum area of the bin. Depending upon which style of fan and heater you use to dry, a static pressure measurement is important. Knowing the static pressure in the plenum can tell the operator the grain depth that works to obtain the best quality, efficiency and capacity.

The Motor Load Monitor Kit provides a normally closed contact which opens when the load on a motor drops below a certain level for a selectable time delay (1-100 seconds). It could also be used to detect an overload on a motor but that feature is not normally used. The kit was originally designed to be used in a Low Level Control Box for shutting down augers when the wet storage tank ran out of grain.

Shivvers standard Channel-Lock Floor features 23% open area, which aids in eliminating static pressure problems incurred in higher grain depths and multiple grain situations. It’s 8” plank with a patented center rib design gives the appearance of two 4” planks side-by-side. This design provides far greater strength, especially with the In-Bin Continuous-Flow Drying and deep depth aeration applications.

Shivvers also offers a Small Grain Floor for canola and other small grains. This floor is designed with an open area of 19.5%, using a 0.054% round hold punch. The small grain floor is also used whenever ultra high capacity sweeps are used as in the Dri Flo 1000 or High Torque Systems.

The Controlled Flow Grain Spreader is designed to spread grain level when other spreaders can’t get the job done. Its special geometric spreader pan gently drops the grain kernels in a unique, even spiraling pattern just where they belong.

The Grain Hog Spreader is a high capacity grain spreader that distributes grain as it is added to the bin, giving a more even air flow throughout your drying bin. The Grain Hog is a large body spreader with your choice of large or small pans, depending on your need, and is fully adjustable from the center hole using an extension wrench.

Shivvers Mini Diverter mounts above the Grain Hog Spreader and directs the grain stream to one side of the spreader while slowly rotating, giving the effect of perfectly centered grain. The Mini Diverter is rated for augers up to 10” diameter, or approximately 3,000 bushels of wet corn per hour.

Heralded as one of the best in the industry, Shivvers heavy duty continuous-flow augers are designed to move hundreds of thousands of bushels of grain annually. As grain is lifted in the bin by the center vertical auger, it is deposited in the center vertical boot.

When multiple bins are used in the system, you may need to add additional horizontal transfer augers with drop outlets to fill the various bins. All horizontal transfer augers are automatically controlled by the CompuDry® Command Center or they could be manually turned on to transfer grain.

The Shivvers Jumpster auger offers the flexibility you need for grain handling after drying. Jump from the horizontal unload auger to a grain transfer device, whether it is an air transfer, elevator leg, loop, or transfer auger. It is designed with an 8” unloader and is adjustable to virtually any angle from vertical to horizontal, or from straight away from the drying bin to a 90° angle to the right.

The slide gate opener provides a helping hand, providing a lever to open the slide gate in the center basket to allow for unloading the bin. It eliminates any strain needed to open the slide gate with the extra weight of grain setting on it.

The floor door allows easy access to the plenum area in your drying bin. They can be installed over each hanger bearing in the unload auger, allowing quick and easy access for maintenance.

The clean-out door is an opening in the bin’s plenum area allowing any fines to be blown out from under the drying floor. By keeping the plenum area clean, air is better able to flow through the floor for grain drying.

Shivvers offers bin reinforcements for standard duty or older grain bins. Bin stiffeners allows these existing bins to be used in situations when they might otherwise need to be replaced before use as a wet holding or drying bin.

Roof vents allow the drying air to be exhausted from the drying bin. During the counter-flow drying process, a large column of heated air is blown into and up through the grain. As the moisture-laden air exits the grain, it moves upward in the bin towards the roof.

The Shivvers Performance System Belt Shield insures safety and offers access to the belts and jaw clutch for easy routine maintenance.